A weboldalon történő látogatása során ún. cookie-kat (sütiket) használunk. Ezek segítik munkánkat abban, hogy Önnek a lehető legjobb szolgáltatást tudjuk nyújtani. Ezek a fájlok nem tárolnak személyes adatokat, csupán a weboldalt látogatók látogatási szokásairól adnak információkat. Az oldalon való továbblépéssel Ön elfogadja a cookie-k használatát. chevron_right Részletek

cancel

Mouldlife MACWAX /wax based / release agent spray 400ml

7 200 Ft
Adóval együtt Szállítás 2 munkanapon belül
Mouldlife MACWAX /wax based / release agent spray 400ml 
Különleges viasz alapú leválasztó anyag, polyurethan, polyester és más műanyag formák leválasztására. Könnyű leválasztás, a porózus felületeket jól tömíti 

MACWAX is a blend of waxes dispersed in rapid drying solvents and packed in aerosol form. This product does not contain CFCs, 111-trichloroethane or any other kind of halogenated solvent.

Special Prooperties: Low mould build up / Easy Release / Good sealing of porous surfaces

MACWAX is suitable for use with many casting materials and a variety of mould types. Typical casting materials are polyurethane epoxy acrylic and polyester. MACWAX is also used extensively for moulding flexible semi-rigid and rigid polyurethane foams.

Leírás

Mouldlife MACWAX /wax based / release agent spray 400ml 
Különleges viasz alapú leválasztó anyag, polyurethan, polyester és más műanyag formák leválasztására. 
K
önnyű leválasztás, a porózus felületeket jól tömíti

MACWAX is a blend of waxes dispersed in rapid drying solvents and packed in aerosol form. This product does not contain CFCs, 111-trichloroethane or any other kind of halogenated solvent.

Special Prooperties: Low mould build up / Easy Release / Good sealing of porous surfaces

MACWAX is suitable for use with many casting materials and a variety of mould types. Typical casting materials are polyurethane epoxy acrylic and polyester. MACWAX is also used extensively for moulding flexible semi-rigid and rigid polyurethane foams.

MACWAX has been formulated for high quality general purpose moulding at temperatures from ambient to 80°C.

MACWAX may be used where a silicone release agent is undesirable such as when the moulded part needs to be painted or bonded.

MACWAX may also be used as a sealant for wood stone cement and other porous surfaces prior to moulding. Very porous substrates may require the application of a specialised sealant prior to application of MACWAX

The material is in a ready to use aerosol. It should be shaken well before use.

The aerosol can should be held 250 mm - 350mm away from the mould surface. The can should be kept moving during the spraying otherwise patches of excess material will form. If possible the spray should be kept perpendicular to the area being sprayed.

The application of a number of light coats is preferable to one heavy coat. Light coats allow the solvent to dry more rapidly and improves the surface finish.

The application technique used will depend upon mould geometry. Deep Sections undercuts and recesses often cause incomplete coverage by parts of the mould surface from the release agent spray. This may lead to difficulty in releasing the moulded parts.

A thin sprayed coat should dry within 2 minutes at 20C. Higher mould temperatures and a current of air over the mould will lead to shorter drying times. Casting onto release agent which has not fully dried may cause softening of the surface of the moulded part.

Termék részletei

Mouldlife MACWAX

Vélemények

Kapcsolódó termékek

(16 egyéb termék az azonos kategóriában)